A cross-hatched sphere is one of the best exercises for learning to build value with lines instead of smooth tone. A sphere shows every part of light and shadow in one shape, and hatching makes you think about each zone on purpose. You decide exactly how many layers of lines each area gets.
If you’d rather start with smooth shading, see how to draw a sphere easily. If you’re not yet sure what cross-hatching is, read how to explain cross-hatching first.
What you need
- An HB or 2B pencil kept fairly sharp (or a fine-liner pen if you want to try ink)
- A 2H or light HB for the construction lines
- Smooth-to-medium drawing paper
- A kneaded eraser
- Something round to trace, such as a cup or roll of tape, if you want a clean circle
A sharp point matters more for hatching than for smooth shading, because the lines need to stay distinct.
Straight hatching vs contour hatching on a sphere
There are two common approaches, and both are worth trying.
Straight cross-hatching uses straight parallel lines in each layer, typically at different angles (for example, one set diagonal, the next set crossing at roughly 90 degrees or at a shallower angle). The roundness comes entirely from where the lines are placed and how many layers build up. This is the simpler method and a good place to start.
Contour (cross-contour) hatching uses lines that curve around the form, like lines of latitude and longitude on a globe. The curve of the lines describes the shape in addition to the value. It’s harder to keep the lines even, but done well it makes the sphere look strongly three-dimensional.
The steps below work for either approach. Just keep your stroke type consistent within each layer.
Step-by-step: cross-hatching a sphere
1. Draw the circle and choose the light
Lightly draw a circle. Trace something round if you like, since this exercise is about value rather than drawing a perfect circle. Decide where the light is coming from. Upper left is a common choice, so the shadow falls to the lower right.
2. Map the value zones
Very lightly, sketch the boundaries of:
- The highlight, a small area facing the light, which you’ll leave as bare paper
- The core shadow, a curved band on the side away from the light, roughly parallel to the edge of the sphere but set in from it
- The reflected light, a thin crescent between the core shadow and the edge on the shadow side
- The cast shadow, an ellipse on the ground, on the side opposite the light, touching the base of the sphere
These lines are just a guide. Keep them faint enough to erase or lose under the hatching.
3. First layer of hatching
Cover everything except the highlight with one even layer of parallel lines in a single direction. Keep the spacing consistent and the pressure light. This layer sets the lightest mid-tone.
For contour hatching, curve these lines around the sphere, following an imagined set of horizontal bands.
4. Second layer
Add a second set of lines at a different angle, crossing the first. This time stop short of the light side, so the second layer covers only the half of the sphere turning away from the light. You now have three values: bare paper, one layer and two layers.
5. Third and fourth layers for the core shadow
Add a third direction just over the shadow side, and a fourth (or simply tighter, slightly heavier lines) concentrated in the core shadow band. The core shadow should end up the darkest part of the sphere itself.
Leave the reflected-light crescent at two layers or so, a little lighter than the core shadow but still clearly darker than the lit side. A common mistake is making reflected light too bright, which breaks the form.
6. Cast shadow
Hatch the cast shadow with as many layers as the core shadow, or one more. Make it darkest right where the sphere meets the ground (the occlusion shadow), and let it lighten slightly as it moves away. Hatching the cast shadow in a different direction from the sphere’s strokes can help separate the two.
7. Refine
Step back and squint. If the transitions look too abrupt, add a few lines at the edge of each zone to soften the steps. If the sphere looks flat, the contrast between the lit side and the core shadow probably needs to be stronger. Erase any remaining construction lines on the lit side.
Tips for cleaner hatching
- Move from the elbow or wrist, not just the fingers. This gives straighter, more even lines.
- Turn the paper. It’s easier to hatch comfortably in one or two directions. Rotate the sheet rather than forcing awkward angles.
- Keep strokes a manageable length. Long lines across the whole sphere tend to wobble. Shorter, overlapping bands of hatching are easier to control.
- Start and end lines lightly where they meet the next zone, so there are no hard ridges between layers.
- Avoid hooks and flicks at the ends of lines. Slow down slightly.
Common problems and fixes
| Problem | Likely cause | Fix |
|---|---|---|
| Sphere looks like a flat disc | Not enough contrast, or no core shadow | Add a darker band set in from the shadow edge |
| Patchy, uneven tone | Inconsistent spacing between lines | Add a fill layer at a new angle to even things out |
| Shadow side looks like a dark rim | Darkest value placed right on the edge | Move the darkest band inward and keep reflected light |
| Lines look scratchy or “hairy” | Fast, flicked strokes | Slow down; use steady, deliberate lines |
| Sphere seems to float | Cast shadow missing or detached | Connect the cast shadow to the base and darken the contact point |
Practice variations
- Change the light. Draw the same sphere lit from the front, the side and behind.
- Limit the layers. Try making a convincing sphere with only two hatch directions.
- Switch to ink. With a fine-liner you can’t erase, so you have to plan the layers. This is useful discipline for pencil too.
- Move on to other shapes. Once the sphere works, try a cylinder and a cube, then an everyday object.
For the bigger picture of how hatching fits with other techniques, see our beginner’s guide to pencil shading.