Shadows do two jobs in a drawing. The shadows on an object show its form, and the shadow it throws onto the ground shows where it sits in space. Getting both right is often what separates a drawing that looks solid from one that looks flat or floating. This guide covers the terms, how to construct a cast shadow, and how to judge the values and edges of each part.
Light and shadow terms at a glance
When a single light shines on an object, you can usually identify:
| Term | What it is |
|---|---|
| Highlight | The brightest spot, where the surface faces the light most directly (most visible on shiny surfaces) |
| Light side / mid-tones | The lit part of the object, getting gradually darker as it turns away from the light |
| Terminator | The boundary where light ends and the form shadow begins |
| Core shadow | The darkest band of the form shadow, just past the terminator |
| Reflected light | Light bounced back into the shadow side from nearby surfaces |
| Cast shadow | The shadow the object throws onto another surface |
| Occlusion (contact) shadow | The very dark area where two surfaces meet and almost no light gets in |
Form shadow vs cast shadow
These two types of shadow are easy to confuse:
- A form shadow is the shadow on the object, on the side that turns away from the light. It describes the object’s shape. On a round object it has a soft, gradual edge. On a box it has a sharp edge along the corner.
- A cast shadow is the shadow the object throws onto something else, such as the table, the wall or another object. It describes the object’s position and the direction of the light.
The core shadow
On a curved object, the core shadow is the darkest part of the form shadow. It sits just past the terminator, where the surface has turned away from the light but before reflected light from the surroundings starts to lighten it again.
A common beginner mistake is to put the darkest value right at the outer edge of the object. In most lighting, the core shadow sits a little inside the edge, with the reflected light between it and the outline. On a sphere it forms a curved band. On a cylinder it forms a straight vertical stripe. Our easy sphere tutorial shows this step by step.
Reflected light
Light hitting the table, a wall or a nearby object bounces back into the shadow side. This makes the edge of the form shadow slightly lighter than the core shadow.
The key point is that reflected light is still shadow. It should be noticeably darker than any part of the lit side. If you make it too bright, the object can look like it has a glowing rim or a hollow “donut” shape. A light-colored surface underneath produces more reflected light. A dark surface produces less.
Occlusion (contact) shadows
Where an object touches the surface it sits on, or where two objects touch each other, very little light can reach. These narrow areas are usually the darkest values in the whole drawing.
A thin, dark occlusion shadow right under the base of a mug or the bottom of a ball does a lot of work. It anchors the object to the surface. Without it, even a well-shaded object can look like it’s hovering.
How to draw a cast shadow
You can draw a cast shadow by observation, simply copying the shape you see, and that’s often the best approach for still life drawing from life. When you’re drawing from imagination, or want to check your observation, a simple construction method helps.
The idea is always the same: a shadow point lies where a light ray passing over the top of the object meets the ground, directly in line with that point’s base.
Parallel light (sun)
The sun is so far away that its rays are effectively parallel. In a simple side or front view:
- Choose a direction and angle for the light.
- From each top point of the object, draw a line at that angle down to the ground.
- From the base point directly under each top point, draw a line along the ground in the direction the shadow falls.
- Where each pair of lines crosses is the corner of the shadow.
- Connect the corners to each other and back to the object’s base.
In a perspective drawing, the ground-direction lines converge toward a point on the horizon, but the principle is the same.
Point light (lamp)
A nearby lamp or candle sends rays outward in all directions, so shadows spread out and grow larger as they move away.
- Mark the light source.
- Mark the point on the ground directly below the light, often called the light’s foot.
- Draw lines from the light through each top point of the object.
- Draw lines from the light’s foot through each matching base point, continuing across the ground.
- Where each pair crosses is a corner of the shadow.
Step-by-step: a cube’s cast shadow
- Draw a cube resting on the ground, and choose a point light above and to the left.
- Mark the light’s foot on the ground below it.
- For each of the cube’s top corners, draw a ray from the light through the corner.
- From the foot, draw a line through the base corner directly beneath each top corner.
- Mark where each ray meets its matching ground line.
- Connect those points. The shadow shape runs from the cube’s base outward to these points.
- Shade the cast shadow darker than the cube’s shadow side, with the darkest occlusion shadow along the base where the cube meets the ground.
Cast shadows of round objects
For a sphere, the cast shadow on a flat surface is roughly an ellipse. It touches the sphere at its contact point and extends away from the light. A light high overhead gives a small, rounder shadow under the ball. A low light stretches it into a long ellipse. A cylinder standing upright casts a shadow shaped like a rectangle with a rounded end.
You don’t need to construct these precisely. The important things are getting the direction right, keeping the shadow connected at the contact point and making its length suit the height of the light.
How light height and distance change shadows
- A high light (such as midday sun or a lamp directly overhead) produces short cast shadows.
- A low light (such as early morning or evening sun, or a lamp close to the table) produces long cast shadows.
- A close point light makes shadows spread out and become larger than the object.
- A distant light makes shadows with roughly parallel sides.
Whatever you choose, keep it consistent. Every object in the drawing should cast its shadow in the same general direction.
Shadow edges: hard and soft
Shadow edges are an often overlooked part of realism:
- Cast shadows are usually sharpest and darkest close to the object and become softer and lighter farther away.
- Small, strong light sources (bright sun, a bare bulb) make crisp shadow edges.
- Large or diffuse light sources (an overcast sky, a big window, a lampshade) make soft, blurry edges.
- Form shadows on curved objects have soft, gradual edges. On flat-sided objects the edge follows the corner, so it’s sharp.
A cast shadow drawn as a uniformly dark shape with a hard outline can look pasted on. Softening the far edge with a light touch or a blending stump often fixes this.
How dark should each zone be?
Exact values depend on the lighting and surfaces, but a typical order from darkest to lightest is:
- Occlusion shadows (darkest)
- Core shadow and the part of the cast shadow nearest the object
- The cast shadow farther from the object
- Reflected light (still in shadow)
- Mid-tones on the lit side
- Light side
- Highlight (lightest)
A 9-step value scale is a useful reference for checking these relationships in your own drawings.
Common mistakes
- No cast shadow at all, so the object floats.
- A cast shadow detached from the object, unless the object really is lifted off the surface.
- Inconsistent shadow directions between objects in the same scene.
- Reflected light too bright, which flattens the form.
- Darkest value on the outline instead of in the core shadow.
- Hard, even shadow edges everywhere, which looks artificial.
Practice exercise
Set a ball, a mug and a small box on a sheet of white paper under a single desk lamp. Draw all three, then:
- Shade the form shadow on each, placing the core shadow in from the edge.
- Add each cast shadow, all falling the same way.
- Darken the occlusion shadow under each object.
- Soften the far edges of the cast shadows.
- Move the lamp lower and draw the setup again, noticing how the shadows lengthen.
For more objects to practice with, see easy object drawing with pencil shading.