Pen and Ink

Ballpoint Pen Drawing Step by Step

Learn ballpoint pen drawing step by step: build tone with light layers, shade a simple 3D object and avoid blobs, grooves and smudges with any cheap pen.

On this page
  1. Why ballpoint is better for drawing than you’d think
  2. What you need
  3. Warm-up: a five-step pressure scale
  4. Step by step: drawing an apple in ballpoint
  5. Shading strokes that work in ballpoint
  6. Making a drawing look 3D
  7. Common problems and fixes
  8. Common questions

Why ballpoint is better for drawing than you’d think

Most people think of the ballpoint as a writing pen, but it has one big advantage for drawing: it responds to pressure. A light touch leaves a pale grey line, and firmer pressure leaves a darker one. You can also stack light layers to build smooth gradients, a bit like graphite. Fineliners, by comparison, give the same dark line however you hold them.

Ballpoints are also cheap, portable and everywhere. That makes them ideal for daily practice. If you’re new to ink, our article can I draw with a pen? explains what to expect.

What you need

  • One or two ballpoint pens. A basic stick pen such as a Bic Cristal is fine. Black or blue both work. A fine and a medium tip give you more range.
  • Smooth paper. Printer paper or a smooth sketchbook is fine. Ballpoint actually behaves well on smooth, inexpensive paper.
  • A scrap of tissue or paper towel to wipe the tip.
  • A scrap sheet under your hand to protect the drawing from smudges.

Warm-up: a five-step pressure scale

Before you start a drawing, spend five minutes on this:

  1. Draw a row of five small boxes.
  2. Leave the first box empty, as the white of the paper.
  3. Fill the second with very light, loose scribbles. Barely let the pen touch.
  4. Fill the third with two light layers.
  5. Fill the fourth with three or four layers, slightly firmer.
  6. Fill the last with as many layers as it takes to get a deep, even dark, without pressing hard enough to dent the paper.

This teaches you the most important ballpoint habit: darks come from layers, not force.

Step by step: drawing an apple in ballpoint

An apple is a good first subject. It’s a simple rounded form, and it teaches you how light wraps around a 3D object. Use a real apple with one lamp shining from the side, if you can.

1. Light construction lines

With the lightest possible pressure, draw a loose circle for the apple’s body. Add a small dip at the top where the stem sits, and a short line for the stem. These lines should be so faint they’ll disappear under the shading later.

2. Refine the outline

Look at the real shape. Apples are rarely perfect circles. They’re often a little wider at the top and slightly lumpy. Adjust the outline with slightly firmer but still light strokes. Don’t draw a heavy, dark outline. In a tonal drawing, edges should mostly come from the shading.

3. Find the light and the shadow

Decide where the light is coming from. Lightly mark three areas:

  • The highlight: a small patch facing the light, which you’ll leave as white paper.
  • The core shadow: the darkest band on the side turned away from the light.
  • The cast shadow: the shadow the apple throws on the table.

4. First layer of tone

Cover the whole apple, except the highlight, with one light, even layer of small overlapping strokes or tiny circles. Follow the curve of the form where you can. This first layer sets a mid-light value.

5. Build the darks

Add more layers on the shadow side. Each new layer should cover a slightly smaller area, moving toward the core shadow. Keep the pressure light and let the build-up do the work. Leave a slightly lighter strip just inside the shadow edge. Light bouncing off the table creates this “reflected light”, and it makes the apple look round.

Darken the stem and the hollow around it.

6. Cast shadow and finishing touches

Shade the cast shadow on the table. It’s darkest right under the apple, where the apple touches the surface, and it softens as it moves away. Then step back and compare the values. Is the darkest part dark enough? Is the highlight still clean? Add a few final layers where needed.

Shading strokes that work in ballpoint

  • Tiny circles (“scumbling”): overlapping small loops give a smooth, even tone that suits skin, fruit and soft surfaces.
  • Hatching: parallel lines in one direction. Good for crisp, graphic shading.
  • Cross-hatching: extra layers at different angles for deeper tones.
  • Contour hatching: lines that curve around the form, which help it look rounded.

For texture ideas like wood grain or stone, see our guide to pen and ink textures.

Making a drawing look 3D

Whether it’s an apple, a cube or a face, a drawing looks three-dimensional when it shows:

  1. A clear light direction, with one side lit and one side in shadow.
  2. A gradual change in tone across curved surfaces, and sharp changes where flat planes meet, like the edges of a cube.
  3. A cast shadow that anchors the object to the ground.
  4. Overlap, where nearer objects partly cover ones further back.
  5. Size and detail falling off with distance, so things further away are smaller and less detailed.

To practise, draw a cube with its top face lightest, one side mid-grey and the other side dark, then add a cast shadow.

Common problems and fixes

  • Blobs of ink: ballpoints collect excess ink at the tip. Wipe the tip on tissue every few minutes, and scribble on scrap before going back to the drawing.
  • Grooves in the paper: you’re pressing too hard. Indented lines stay white when you shade over them later. Layer instead.
  • Smudging: ballpoint ink sits on the surface for a moment. Keep a scrap sheet under your hand, and left-handers may find it easiest to work from right to left.
  • Patchy tone: use smaller strokes, and change stroke direction between layers so the marks blend.
  • Shiny darks: heavy ballpoint layers can turn glossy. Stop a step earlier, or accept the shine as part of the medium.

A note on keeping your work: many ballpoint inks fade with long exposure to light, so store finished drawings in a sketchbook or folder rather than in a sunny spot.

Common questions

Can I draw with any pen?

Yes, more or less. Ballpoints, gel pens, fineliners and fountain pens all work. Each behaves differently, though. Ballpoint gives you pressure-controlled tone, and a fineliner gives a uniform dark line that you shade with hatching or dots. For an overview, see our guide to pens for pen and ink drawing.

What can an 11-year-old draw with a ballpoint?

Simple, everyday subjects are perfect: fruit, a mug, a shoe, a pet asleep, a houseplant, a cartoon character or a doodle pattern. A ballpoint is a good tool for older children because it’s cheap and forgiving of light layering. Our list of easy things to draw with a pen has more ideas.

Should I sketch in pencil first?

You can, but with a ballpoint it’s often unnecessary. Very light ballpoint construction lines do the same job, and they disappear under shading. If you do use pencil, keep it faint. Erasing over ballpoint can smear fresh ink, so wait until it’s fully dry.

The complete guide to pen and ink

The Best Pens for Pen and Ink Drawing
Read the guide

Keep exploring

Guides from other topics

All topics →