Pen and Ink

Pen and Ink Textures: Wood, Stone, Fabric and Foliage

Pen and ink texture techniques for wood, stone, fabric and foliage: the marks to use, how to keep texture from flattening form, and practice swatches to try.

On this page
  1. The basic idea: texture follows form and light
  2. Your mark-making vocabulary
  3. Wood
  4. Stone
  5. Fabric
  6. Foliage
  7. Keeping texture from taking over
  8. Practice: a texture swatch sheet

The basic idea: texture follows form and light

A texture in pen and ink isn’t just a pattern you fill shapes with. To look convincing, it needs to do two things:

  1. Follow the form. Marks should wrap around curves, change direction on different planes and get smaller as surfaces recede.
  2. Respond to light. Texture should be strongest in the shadows and mid-tones, and fade almost to nothing in the lit areas. In bright light, surfaces look smoother because shadow is what reveals texture.

Keep those two rules in mind and almost any texture will look right.

Your mark-making vocabulary

Every texture below is built from a small set of marks:

  • Hatching: parallel lines.
  • Cross-hatching: layered sets of parallel lines at different angles.
  • Contour hatching: lines that curve along the surface of a form.
  • Stippling: dots. See our stippling guide.
  • Scribbling: loose, continuous looping or zigzag lines.
  • Broken lines: lines with small gaps, which suggest light, age or roughness.
  • Flicks: short strokes that taper as you lift the pen, used for grass, fur and bark.

A fine fineliner (0.1–0.3 mm) is the most versatile tool for texture. A brush pen or dip pen adds variety. See what pen should I use for line art for sizes.

Wood

Planks and boards

  • Draw grain lines running the length of the board, slightly wavy, and roughly parallel without being perfectly so.
  • Add knots as small ellipses, with grain lines curving around them like water around a stone.
  • Leave gaps between lines in lit areas and pack them closer in shadow.
  • Darken the cracks between planks with a solid line, and add a thin shadow on one side.

Weathered wood

  • Use broken, irregular grain lines with occasional splits drawn as dark, tapering lines.
  • Add small nail holes as dots with a tiny shadow, and splinters along edges.
  • Let the ends of boards break up and look ragged.

Tree bark

Bark varies by species, so look at a real tree. Common approaches:

  • Ridged bark (like oak): long vertical shapes with dark crevices between them. Shade the crevices heavily and leave the ridges mostly white.
  • Smooth bark (like beech): very little texture, just a few horizontal marks and soft shading with contour hatching around the trunk.
  • Peeling bark (like birch): horizontal dashes and patches, with dark areas where bark has lifted.

Whatever the species, curve the marks around the trunk so it looks cylindrical, and darken one side.

End grain and cut logs

Draw concentric, slightly irregular rings from the centre outward, with a few radial cracks. Shade the bark edge darker.

Stone

Rocks and boulders

  • Start with an angular outline. Rocks have planes, not smooth curves.
  • Decide on the light direction and shade the planes facing away with hatching or cross-hatching.
  • Add cracks as dark, irregular lines that branch and taper.
  • Use stippling or small irregular dots on the surface to suggest grain, concentrated in shadow.

Brick and stone walls

  • For brick, draw staggered rows of rectangles. Don’t draw every brick. Draw a cluster of them and let the rest fade out, so the viewer fills in the gaps.
  • Leave mortar lines light, and shade one edge of each brick (bottom or side, away from the light).
  • For rough stone walls, draw irregular rounded shapes that fit together, with dark gaps between them.
  • Add a few chips, cracks or patches of moss for character.

Smooth stone and pebbles

Use contour hatching or stippling that follows the rounded form, with a clean highlight and a cast shadow. Keep surface marks minimal.

Fabric

Folds

Fabric texture is mostly about folds. Common types include:

  • Pipe folds: tube-like folds where fabric hangs from a point, such as curtains.
  • Zigzag folds: where fabric bunches, as at the back of a bent knee.
  • Spiral folds: around a cylinder, such as a rolled sleeve.
  • Drop folds: where fabric falls over an edge, such as a tablecloth.

Shade the inside of folds with contour hatching that follows the curve of the cloth. Leave the top of each fold light. Use a darker accent where folds tuck under.

Fabric types

  • Silk and satin: sharp contrast, with bright highlights next to dark shadows and smooth hatching.
  • Cotton and linen: softer contrast, with moderate folds.
  • Wool and knits: rounded, chunky folds, with small “V” or loop marks for knit texture in shadow.
  • Denim: heavier, stiffer folds, with fine diagonal hatching to suggest the twill weave.
  • Velvet: dark overall, with light only on the ridges of folds.

Patterns on folded fabric

If fabric has stripes, checks or a print, the pattern must bend with the folds. Stripes curve over a fold and disappear into the crease. Draw the folds lightly first, then add the pattern following them.

Foliage

Trees at a distance

  • Don’t draw individual leaves. Draw clumps: irregular masses with a light side and a dark side.
  • Use scribbled loops or bumpy outlines for the clump edges.
  • Fill shadow areas with dense scribble or cross-hatching, and leave the lit tops of clumps almost empty.
  • Show a few sky holes, gaps where you see through the canopy.

Nearby leaves

  • Draw a few leaves in detail, with outline, centre vein and a touch of shading, and let the rest become simpler shapes or silhouettes.
  • Overlap leaves to create depth, and shade the ones behind slightly darker.
  • Vary leaf angles. Leaves seen edge-on look like thin lines.

Grass and hedges

  • Grass: quick upward flicks, denser at the base and in shadow. Don’t draw grass everywhere. A few clumps suggest a whole lawn.
  • Hedges: a textured mass, much like a distant tree, with a darker base and some individual leaf shapes along the top edge.

Keeping texture from taking over

  • Less texture in the light, more in the shadow.
  • Less texture in the distance, more up close. Detail falls off with distance.
  • Focus texture where you want attention. Let other areas stay simple.
  • Don’t outline then fill. Let texture define edges where possible.
  • Step back often. Texture that looks right up close can look busy from a distance.

If you’d rather add tone with washes than marks, try combining these textures with ink wash, or with colour in line and wash.

Practice: a texture swatch sheet

Divide a page into a grid of small squares, about 4 cm each. In each square, draw one texture:

  1. Wood planks with a knot
  2. Weathered wood
  3. Ridged tree bark
  4. Rough rock with cracks
  5. Brick wall
  6. Pebbles
  7. A silk fold
  8. A knitted wool fold
  9. A tree clump
  10. Grass
  11. A leafy branch
  12. A texture of your choice: fur, rust, water or sand

Label each square and keep the sheet. It becomes your personal reference for future drawings. If you need simple subjects to apply these textures to, see easy things to draw with a pen.

The complete guide to pen and ink

The Best Pens for Pen and Ink Drawing
Read the guide

Keep exploring

Guides from other topics

All topics →